Accredited Calibration Lab in accordance with ISO/IEC
Our cal lab is accredited by A2LA in accordance with the International Standard ISO/IEC 17025. We provide high quality calibration services under the circumstances that calibration according to ISO/IEC 17025 has been given an importance.
A2LA Accredited Calibration
| Equipment | Range | Reference | Item |
|---|---|---|---|
| Antenna (Broadband, Horn) |
30 - 1000 MHz (RAM) 1 - 18 GHz (SSM) 25 - 3000 MHz |
ANSI C63.5, VCCI-V10 ANSI C63.5 SAE ARP958 |
Antenna Factor |
| Rod Antenna | 9 kHz – 50 MHz (ECSM) | ANSI C63.5 CISPR 16-1-4, CISPR 25 SAE ARP958 |
Antenna Factor |
| Loop Sensor (e.g. Solar 9229-1) |
5 Hz – 300 kHz | MIL-STD-461 | Antenna Factor |
| Pre Amplifier | 10 Hz – 26.5 GHz | EMC Kashima Procedure | Gain |
| Attenuator | 10 Hz – 26.5 GHz | EMC Kashima Procedure | Attenuation |
| Coaxial Cable | 10 Hz – 26.5 GHz | EMC Kashima Procedure | Insertion loss |
| EMI Receiver | Band A Band B Band C Band D Band E 18-40 GHz |
CISPR16-1-1 Ed.3 EMC Kashima Procedure |
Input Impedance Pulse Response Relative Pulse Response Sine-Wave Selectivity (6dB BW) Impulse Bandwidth CISPR-AV Verification Frequency Level |
| Spectrum Analyzer | 10 Hz – 40 GHz | Manufacturer Procedure EMC Kashima Procedure |
Cal out Frequency Tracking Generator |
| Signal Generator | 10 Hz – 40 GHz | EMC Kashima Procedure | Frequency Level AM modulation Modulation Frequency |
| LISN (AMN / AN) | 9 kHz -200 MHz | CISPR 16-1-2 +A2 CISPR 25 ISO 7637-2 ANSI C63.4 |
Insertion Loss (VDF) Impedance Phase Isolation VSWR |
| ISN (only TESEQ) |
150 kHz – 30 MHz | CISPR 16-1-2 CISPR 22 Manufacturer Procedure |
CM Impedance Phase angle VDF Isolation LCL |
| E- Field Probe | 10 kHz – 4000 MHz 100 MHz |
IEEE Std 1309 | Correction Factor Linearity Rotational Response |
| Magnetic Field Meter | 1.26 μT – 63 μT (50, 60 Hz) |
IEC 61786 | Frequency Response |
| CDNs | 150 kHz – 230 MHz | EMC Kashima Procedure | Coupling Factor Impedance |
| (150 to 50) Ω Adpt. | 150 kHz – 230 MHz | EMC Kashima Procedure | Insertion Loss |
| Directional Coupler | 9 kHz – 8.5 GHz | EMC Kashima Procedure | Insertion Loss Coupling Factor Isolation |
| BCI Probe | 9 kHz – 2.1 GHz | EMC Kashima Procedure | Insertion Loss |
| BCI Probe Fixture | 9 kHz – 2.1 GHz | EMC Kashima Procedure | VSWR |
| Current Probe | 9 kHz – 1000 MHz | CISPR 16-1-2 | Transfer Impedance |
| ESD Simulator | ±2, 3, 4, 6, 8, 15, 20 ±2 kV – 40 kV |
IEC 61000-4-2 ISO 10605 |
Current Rise / Fall time RC Time Constant Charging Voltage |
| EFT/Burst Generator | 0.25 kV – 4 kV | IEC 61000-4-4 +A1 | Peak Voltage Rise / Fall time Impulse 50% Burst Duration Burst Period Repetition Rate |
| Surge Generator | 0.5 kV – 4 kV | IEC 61000-4-5 | Voltage (Open) Current (Short) Rise / Front time Time to half value Duration time Over / Under Shoot Phase Shift |
- Other instruments and the change of calibration range in the upper and the lower limits are accepted as general calibration.
- The minimum uncertainty value is based on our test sites measurement.
- If you need to witness calibration service, please feel free to ask us.
- Please contact us for further information regarding dates and fees.
